Black Widow Security BW 3 Channel Manual do Utilizador

PAGE-1 UPDATED 11-5-2014 Rev.3 RED WIDOW Detailed installation manual

PAGE-10 UPDATED 11-5-2014 1.5 Select one Red Widow bottom clamp and place the clamp over the stud and set

PAGE-11 UPDATED 11-5-2014 1.7 Select the third 3/8” serrated flange nut. Thread the nut on the support s

PAGE-12 UPDATED 11-5-2014 STEP 2: Marking panel and footing layout Note: Before applying mounting a

PAGE-13 UPDATED 11-5-2014 2.3 Use a calculator to multiply panel width by the amount of panels going to

PAGE-14 UPDATED 11-5-2014 2.6 Move to the left/bottom of the layout and mark the first footing position

PAGE-15 UPDATED 11-5-2014 2.9 Make all horizontal footing marks in between the le

PAGE-16 UPDATED 11-5-2014 STEP 3: Cut composite shingle 3.1 Use one base plate from

PAGE-17 UPDATED 11-5-2014 3.4 When completed the trimmed section of composite shingle should appear as sh

PAGE-18 UPDATED 11-5-2014 STEP 4: Attachment of RED WIDOW mounting system 4.1 Remove

PAGE-19 UPDATED 11-5-2014 4.4 Upon completion of step 4 all racking must be orientated as shown.

PAGE-2 UPDATED 11-5-2014 SpiderRax, Inc. REVISION PAGE Installation Manual For RW-S, RW-B D

PAGE-20 UPDATED 11-5-2014 STEP 5: Install flashing 5.1 Apply flashing mastic to the bottom of

PAGE-21 UPDATED 11-5-2014 Step 6: Final positioning & module installation 6.1 Start

PAGE-22 UPDATED 11-5-2014 6.4 Adjust all mounts to desired height using the adjustm

PAGE-23 UPDATED 11-5-2014 6.7 Adjust the overhang of the panel to no more than 12” from center o

PAGE-24 UPDATED 11-5-2014 STEP 7: Grounding Parts required for ground lug assembly  One ILSCO, Ground

PAGE-25 UPDATED 11-5-2014  Two ¼” serrated star washer Patent pending P/N: RW-S,

PAGE-26 UPDATED 11-5-2014 Assembly & Attachment 7.1 Select one ground lug and insert one ¼” x ¾” x 2

PAGE-27 UPDATED 11-5-2014 7.3 Select one Grounding set screw. Thread the set screw in the ground lug with t

PAGE-28 UPDATED 11-5-2014 7.6 Use a torque wrench and tighten the ¼” hex nut to 12 ft-lbs. This will bon

PAGE-29 UPDATED 11-5-2014 STEP 8: Quality inspection & clean up 8.1

PAGE-3 UPDATED 11-5-2014 RED WIDOW INSTALLATION INDEX Page 1…………………………………………………………………………….………………………………………

PAGE-4 UPDATED 11-5-2014 SPIDER RED WIDOW RAX

PAGE-5 UPDATED 11-5-2014 TOOL LIST  Cordless impact wrench with a ¼” adapter fitting 

PAGE-6 UPDATED 11-5-2014 STEP 1: RED WIDOW assembly Parts required for step 1. 1. One Red Widow base

PAGE-7 UPDATED 11-5-2014 3. Three 3/8” serrated flange nuts P/N FN-H38S 4. One Red Widow top mount

PAGE-8 UPDATED 11-5-2014 1.1 Select one RW support stud and one 3/8” serrated flang

PAGE-9 UPDATED 11-5-2014 1.3 Center the stud in the stud track and turn the stud clockwise until the stud