Black Widow Security BW X-Z Series Manual de Instalação descarregar pdf

INSTALLATION MANUAL

3RP / 5RP 4-BUTTON SERIES

VEHICLE SECURITY SYSTEMS

Before you begin the installation

•

Read the INSTRUCTIONS!

• Always use a multi-meter when verifying

vehicle wiring.

•

Before mounting the product,

verify with

the customer the desired location for the

program switch and LED.

•

Protect the vehicle by using fender

covers.

•

Always look before drilling. Make sure

you will not cause damage to vehicle

hoses, electrical looms or physical damage

to vehicle.

•

Program the dip switches on the module

first (see dip switch information).

Installation Instructions

Mounting System Module

Mount the system module under the dash

where it will be difficult for a potential

thief to locate the module, and away from

moving parts such as brake pedals, etc.

Route the antenna wire away from wire

looms, computer modules and metallic

objects for better range.

Mounting Siren

Mount the siren in a suitable place under

the hood, away from hot and moving

engine parts such as manifolds, fan belts,

etc. Make sure the siren cannot be

accessed from underneath the vehicle or

through the grill. Face the siren down so

that water cannot accumulate inside the

siren bell. Protect wires running through

the firewall using either tape or split loom

tubing. If a new hole is needed, protect the

wire from chaffing by installing a proper

size grommet.

Mounting Shock Sensor

Secure the shock sensor to the steering

column, thick wire harness or a dash

brace, using a wire tie. Make sure that the

adjustment screw is accessible for later

testing and adjustment.

1 2 3 4 5 6 ... 11 12

Resumo do Conteúdo

Página 1 - INSTALLATION MANUAL

INSTALLATION MANUAL3RP / 5RP 4-BUTTON SERIESVEHICLE SECURITY SYSTEMSBefore you begin the installation•Read the INSTRUCTIONS!• Always use a multi-meter

Página 2 - Dip Switch Settings

SYMPTOMAlarm doesn't Arm/Disarm.Alarm will not Passively Arm.Alarm will not enter CodeLearning Mode.Alarm chirps 4 times 30seconds after system i

Página 3 - Default Reset

SYMPTOMIlluminated Entry does notactivate on upon disarm.Range is poor.Vehicle starts when armed.Car will not start whensystem is disarmed.Keyless ent

Página 4 - 3 Relay Systems

If the power trunk releaserequires a positive pulse tooperate, use this circuit.GRAY(AUXILIARY 2OUTPUT)+12VPOSITIVETO SOLENOIDTRUNK RELEASE CIRCUIT DI

Página 5

Dip Switch SettingsSwitch #1 = Lock/Unlock Pulse Time: ON = .75 seconds OFF = 3 secondsSwitch #2 = Ignition Triggered Door Locks: ON = Ignition Lock O

Página 6 - RECEIVER

Programmable FeaturesStep Function Button 1 (On) Button 2 (Off)1. Parking Light Operation Car Locator Feature Normal2. Door Unlock Pulse Single Double

Página 7 - (w/o on-board lock relays)

4on. If the vehicle’s parking light circuit exceeds10 amps a relay is required. For vehicle’s withindependent left and right parking light circuits,th

Página 8

55 Relay Systems (Built-in relays)5-Pin White Door Lock Connector: Plug-inconnector port for door lock harness (see 5relay door lock diagrams).• WHITE

Página 9 - (with on-board lock relays)

6BLUEWHITEGREENNO CONNECTIONNO CONNECTIONNEGATIVE UNLOCK OUTPUT (-)(-) AUXILIARY 2 OUTPUT+12V IGNITION(+)12V12V FLASHINGLIGHT OUTPUT(10 AMPS)(+) DOOR

Página 10

7POSITIVE PULSE DOOR LOCK SYSTEM87858687a3087858687a30GREENBLUEBROWNVIOLETWHITEN/CN/CN/CTO DOOR LOCK RELAY TO DOOR UNLOCK RELAYFUSED 12V+DOOR LOCKHARN

Página 11

8BLUEWHITEGREENLOCK SWITCH (87a)LOCK MOTOR (30)UNLOCK MOTOR (30)(+)12V12V FLASHINGLIGHT OUTPUT(10 AMPS)5-RELAYRECEIVERMODULESHOCKSENSOROPTIONALSENSORB

Página 12 - If the power trunk release

9POSITIVE PULSE DOOR LOCK SYSTEMFUSED 12V+WHITEGREENBLUEBROWNVIOLETN/CLUDOORSWITCHRELAYMODULEN/CNEGATIVE PULSE DOOR LOCK SYSTEMGROUNDWHITEGREENBLUEBRO